3360

Antique Factory Documented Colt Single Action Army Revolver with Extremely Rare Bridgeport Patent Ri

Currency:USD Category:Antiques / Firearms & Armory Start Price:9,000.00 USD Estimated At:18,000.00 - 27,500.00 USD
Antique Factory Documented Colt Single Action Army Revolver with Extremely Rare Bridgeport Patent Ri
Buyer's Premium is 20.5% by credit card, reduced to 18% if payment is made by cash, check or wire transfer. Contact Rock Island Auction Company to complete your registration with the auction house.

Estimate: $18000 - 27500
Colt Single Action Army revolver with Colt factory letter that states the revolver was shipped from Colt to J.F. Schmelzer & Sons in Kansas City, Kansas, on December 28, 1898. The letter describes the revolver as caliber ".32/20" with 7 1/2 inch barrel, "nickel" finish and "rubber" stocks. The side of the front grip strap is inscribed "Bill Keanne Melrose Montana". It is preceeded with two eagle feather. History of this individual is unknown. The hammer screw is a special screw with over-sized button head. The revolver is accompanied by a light weight russet leather small loop cartridge belt with the Flatau device which consists of a two-prong, slotted, spring steel clip riveted to an arched, rectangular backplate. The backplate is attached to the belt by four copper rivets. The spring clips engage the revolver hammer screw and attach the revolver to the belt. The revolver can be quickly disengaged from the clips or swiveled and fired from the belt. The spring clips are stamped: "BRIDGEPORT G.I. CO" and PAT'D JAN 17. 1882" patented by Louis S. Flatau of Pittsburg, Texas in 1882 and manufactured by the Bridgeport Gun Implement Company of Bridgeport, Connecticut. Approximately 500 units were manufactured for U.S. Army trial issue. A smaller number of the Bridgeport Rigs were manufactured for the civilian market. Surviving examples of Bridgeport Rigs are rare. The revolver has a full nickel plated finish and is fitted with two-piece black hard rubber checkered grips with the Rampant Colt trademark in an oval at the top. The revolver has the late oval ejector rod head, smokeless powder frame, hammer with bordered knurling on the spur, and cone-shaped firing pin. The top of the barrel is roll-stamped with the late, elongated block legend; "COLT'S PT. F.A. MFG. Co. HARTFORD CT. U.S.A." in one line. The left side of the barrel is roll-stamped "32 W.C.F." "V" and the caliber designation "32" are stamped on the underside of the barrel ahead of the frame. The left side of the frame is roll-stamped with the Colt three-date/two-line patent markings followed by the circled Rampant Colt trademark. The assembly number, "227" is stamped on the inside of the loading gate. A "V" inspection mark is stamped on the rear face of the cylinder and in the hammer slot above the firing pin hole. The full serial number, "182226" is stamped on the bottom of the frame, trigger guard, and backstrap. The partial serial number "226" is stamped on the rear face of the cylinder. All of the visible serial numbers match.
BBL: 7 1/2 In
Stock:
Gauge: 32 WCF
Finish: nickel
Grips: black hard rubber
Serial Number: 182226
Condition: Extremely fine. The revolver retains 85% of the original factory nickel plated finished with scattered, light handling wear. The black hard rubber grips have faded to brown and the checkering shows handling wear. The revolver markings are crisp. The action is tight and functions well. The cartridge belt is fine with flaking on the edges and on the cartridge loops. The device retains about 80% of the nickel plated finish with some age discoloration. The markings are clear. A Colt Single Action Army Bridgeport Rigs is a rare and unique handgun/cartridge belt combination seen only in advanced collections. This rare and unique set obviously have been together for a long time and the Montana individual inscription should be researched.